News
While there are a few other brands, the hard drive market is essentially a three-horse race between WD, Seagate and Toshiba.
Having looked at WD and Seagate NAS HDDs recently, it seemed appropriate to look at what Toshiba offers that’s different to the other two.
Toshiba Electronics Europe launched the N300 NAS drive series in January 2017. By that point, Western Digital and Seagate had been in the dedicated NAS drive market for years. WD Red has been on sale since 2012, and Seagate IronWolf launched in 2016. Toshiba was late to this party, and that certainly coloured its product range from the outset.
The N300 launched at 4TB, 6TB, and 8TB, all carrying a 128MB data buffer and a 7200 RPM spindle. That last detail is the key one. Toshiba did not try to match WD and Seagate on their terms; instead, it went faster.
The N300 range runs at 7200 RPM on every capacity variant, from the smallest to the largest. That decision produces a drive with meaningfully higher sequential throughput. The N300 achieves up to 298 MB/s sustained transfer speed. The WD Red Plus manages around 180-190 MB/s. The IronWolf reaches 202 MB/s. The N300 leaves both behind in raw sequential performance.
And, this newer HDWG740EZSTC model covered here offers 512MB of cache, where older revisions had 128MB or 256MB.
However, there are tradeoffs here. On the hardware side, the additional rotational speed makes the N300 noisier, it generates more heat, and uses more power. That makes it less suitable for a NAS that’s sitting on the desktop, and more acceptable if you have a server room. And, the other awkward aspect of the N300 is that Toshiba has jacked the price up of this drive to around 50% more than what WD and Seagate are asking for the same capacity from some sources.
There are a few deals to be had on the N300, but it does make you wonder whether it's competing with the WD Red Plus and Seagate IronWolf, or the Red Pro and IronWolf Pro?
If only Toshiba would price the N300 more appropriately, it might become one of the best NAS drive options.
Toshiba N300 4TB: PriceWithout doubt, the worst possible place to buy the N300 4TB drive is from Amazon.com and the Toshiba Store on that retailer.
The current asking price there is around $330, which is utterly outrageous. To put that into perspective, in January 2026, the price was $215.62, and in August 2025, it was $154.99. Therefore, it has seen a 212% price increase in just nine months. Given that I wouldn’t believe there is much interest in 4TB drives for Datacentres, this is purely corporate greed in action.
But what’s even more curious is that even in the US, you can get this drive for cheaper, since B&H Photo sells it for $244.99, and Newegg wants $299.
Outside of the US borders, the prices are still elevated but not as excessively. From Amazon.co.uk, the 4TB capacity is priced around the £200 mark, and across Europe on Amazon, it's €237.86, if they have stock.
For comparison, American customers on Amazon.com can pay $194.99 for the 4TB WD Plus drive, and the 4TB Seagate IronWolf is only $189.
In short, wherever you buy the N300, it's seen a much larger price increase than its competitors, and this is true across all regions.
One important difference to note is that the N300 is available in a much larger range of sizes than Red Plus and IronWolf. The smallest N300 is 4TB, and it is available in 6TB, 8TB, 10TB, 12TB, 14TB, 16TB, 17TB, 20TB and 22TB.
The Red Plus only goes from 1TB up to 12TB, and the IronWolf goes from 1TB to 16TB, with some truly odd sizes such as 7TB in between the usual capacity increases.
However, you look at the N300 pricing, this is an expensive drive that tries to go between the Red Plus/IronWolf and the Red Pro/IronWolf Pro product ranges.
What makes this more complicated is that while officially IronWolf Pro drives are made in 4TB capacities, I could only find 12TB and larger. But the 4TB WD Red Pro can be found for $249.99 on Amazon, which is cheaper than the N300 for the same capacity.
What’s genuinely confusing about the N300 range is that if you go looking for drives of a particular capacity, you might find that drive with three different part numbers, one being the retail number, others being OEM, and I managed with some sizes to find ones with 128MB, 512MB and 1024MB caches. Obviously, the larger caches are better, especially on bigger capacity drives.
As an example of how messed up Toshiba is on Amazon.com, clicking “Visit the Toshiba Store” sometimes takes you to Toshiba kitchen products.
These prices need to be more consistent and gouge less.
(Image credit: Toshiba)Toshiba N300 4TB: DesignSince its launch, Toshiba has developed several proprietary technologies for the N300 and has kept them consistent across the product line.
These include Stable Platter Technology, which uses a tied spindle motor to secure the drive shaft at both ends. This reduces system-induced vibration and is directly comparable with WD's 3D Active Balance Plus approach. Both address the same problem, where in a multi-drive enclosure, vibration from one drive affects the others.
Also special to the N300 is Dynamic Cache Technology, a self-contained algorithm with on-board buffer management that optimises cache allocation between read and write operations in real time. From the outset, the N300 has typically had more cache than its competition, so managing the use of that is important for performance.
One of the hidden issues with faster-rotating drives is wear, and on the N300, this is addressed in a few interesting ways, one being Ramp Load Technology. This parks the read and write heads on a ramp outside the platter surface when the drive is idle. It reduces head wear during power cycles and protects the media surface.
Error recovery control has also been present since the original launch, limiting recovery time to avoid RAID array ejections in the same way that WD's TLER does.
(Image credit: Mark Pickavance)All these features I’ve mentioned arrived with the first N300 drives, but since then, the N300 has undergone some subtle changes, one of which is the introduction of NASLink Technology.
This fine-tunes drive behaviour for rapid data access and includes firmware-level optimisation for RAID performance through improved disk coordination. The more drives you have in an array, the more important it is that they’re all moving to a common beat, and Toshiba has baked that into the N300 via firmware updates.
Having larger arrays improves performance, but it introduces vibrations that can migrate from one drive to those either side of it. To combat this, the N300 also carries three built-in rotational vibration sensors. These detect and compensate for the knock-on vibration effects that become a serious problem once a NAS enclosure has more than four drives installed.
Overall, while Toshiba hasn’t come up with anything like Seagate IronWolf Health Management. In other respects, this is probably the most sophisticated drive serving the home and small-business NAS market.
However, when Toshiba only offers a three-year warranty and 180TB/year workload, it doesn't seem much like it's that special.
(Image credit: Mark Pickavance)Toshiba N300 4TB: Performance(Image credit: Mark Pickavance)Since Toshiba only provided two of these drives, there seemed little point in trying to work out what array advantages running the N300 offered. Therefore, I went with the same PC analysis that I used on the WD Red Plus and IronWolf drives
Here are my results:
Drives
Toshiba N300
WD Red Plus
IronWolf
Part No.
HDWG740
WD40EFPX
ST4000VN006
Capacity
4TB
4TB
4TB
Cache
512MB
256MB
256MB
Rotational Speed
RPM
7200
5400
5400
AJA
Read
MB/s
282
187
190
Write
MB/s
283
179
185
ATTO
Read
MB/s
291.57
206.24
192.35
Write
MB/s
294.25
197.35
191.76
CrystalDiskMark Default
Read
MB/s
299.18
201.23
200.77
Write
MB/s
300.50
208.26
199.33
CrystalDiskMark RealWorld
Read
MB/s
286.95
212.46
200.22
Write
MB/s
290.01
204.42
199.11
PCMark
Score
651
801
677
Bandwidth
MB/s
99.87
124.49
103.69
MS Winsat
Random 16 Read
MB/s
2.37
1.71
1.6
Sequential 64.0 Read
MB/s
218.38
168.53
158.16
Sequential 64.0 Write
MB/s
289.31
204.65
190.5
Read Time with Sequential Writes
ms
4.810
1.385
1.946
Latency: 95th Percentile
ms
31.620
12.685
34.685
Latency: Maximum
ms
75.357
64.723
62.341
Average Read Time with Random Writes
ms
12.021
5.267
9.898
Aside from PCMark10, all other tests show that the N300 is a country mile faster than either of the alternative NAS drives with the same capacity. I can put those results down to the increased rotational speed and also the 512MB cache on the N300.
One extra test I did perform on a NAS was to take a single drive on a Ugreen NASync DXP4800 Plus NAS, connect to it over a 2.5GbE LAN link, and bench test it from my PC.
I achieved read and write speeds over 285MB/s, which is the practical limit of 2.5GbE LAN ports. That with a single N300 drive, you can saturate a 2.5GbE Link is impressive, and it implies that with four drives in a RAID 5 configuration, you should be able to saturate a 10GbE LAN port. To do that on both WD and Seagate would involve moving up to their Red Pro or IronWolf Pro range.
Based on these numbers alone, the N300 might be worth what Toshiba is asking for it, depending on how your NAS is configured and if raw speed is important to that system.
However, I should also point out that the power consumption on the N300 is dramatically more than on the Seagate and WD drives. The current 4TB N300 draws 7.43W typical under active operating load, where the Red Plus only consumes 4.7W and the IronWolf 4.8W.
And, the N300 will be converting most of that power into heat, regrettably. If you already have a machine room where the cooling isn't coping, then maybe using these drives might not be the best plan.
Toshiba N300 4TB: Final verdict(Image credit: Mark Pickavance)If this drive were cheaper and Toshiba had technology like the IronWolf Health Management scheme, there would be little debate about this being one of the best options.
However, there are a few things about NAS and RAID arrays that make this choice slightly more complicated.
For starters, the majority of NAS are bottlenecked by their LAN connections, so if you only have a NAS with a 1GbE or 2.5GbE LAN port, then you won’t see the improved performance of the N300 over the WD Red Plus or IronWolf. If you do have a 10GbE LAN port, it will be saturated with four drives; extra drives won’t make any difference unless you have multiple LAN ports and bandwidth aggregation.
What you do get with the N300 is internal NAS performance, which, if you are running AI on your NAS, might be a factor. However, most people using their NAS that way use NVMe drives for caching, allowing them to get higher performance from 5400RPM drives. Rebuilds will be quicker, but the value of that comes down to whether the NAS is a point-of-service or other mission-critical function, and it assumes that a drive (or drives) dies in the first place to trigger the rebuild.
The fly in this ointment is the price, because for a four bay NAS, that’s a jump from roughly $800 in storage to $1200, and for that increase, you might consider Pro-level media.
Interestingly, currently the WD Red Pro 4TB is $250, offers 7200RPM spindle speeds, for less than the 4TB N300 on Amazon.com. And deals on IronWolf Pro models undercut Toshiba's pricing at that retailer.
In the UK, the IronWolf Pro 4TB is only £169.99, the WD Red Pro is £234.75, making the £195.15 N300 4TB a better deal than the WD, but much worse than the Seagate drive.
That’s the biggest issue here, because Toshiba aimed this product to hit the open ground between the entry-level NAS drives and the Pro series mechanisms, and now adjusted the price to compete with the premium layer. These Pro drives have 300TB/yr workload ratings and a 5-year warranty, whereas the N300 only has 180TB/yr and a 3-year warranty.
Based on these Toshiba defined ratings, it can't compete on reliability.
While I expect that if I tested the N300 against the Pro hardware, it would do well, since both of the competing brands typically only include 256MB of cache, not 512MB. But those who buy those mechanisms are looking for longevity above all else.
Overall, I liked the N300, as it takes less time to get operational on a NAS and in small arrays, the performance is excellent. But I can’t get on board with Toshiba’s pricing, which seems excessively high in some regions and lacks any consistency.
For more storage solutions, we've reviewed the best NAS devices.
Philips Hue bulbs are a hugely popular smart lighting solution, and with good reason. But if your setup consists only of Hue bulbs (and a hub), you're missing a trick. The brand makes a range of accessories that can make a major difference to how you use your smart lights, and most are very affordable too. I asked the TechRadar team for some of their favorite cheap smart home upgrades, and almost all the answers I got back were Philips Hue accessories, so I decided it was worthy of its own article.
Entertainment Editor Matt Bolton is a big fan of his Philips Hue Smart Button, a compact, simple, wireless switch. "I stuck the Smart Button on my wall next to my regular light switch, giving me a way to control just the lamps in my living room separate to the other lights," he says. "It's so nice and easy, and no rewiring needed."
Matt also makes use of the Philips Hue Smart Plugs, which can be used to integrate non-smart lights into your Hue ecosystem. "I use the Hue Plugs to add little lamps that are too small for Hue bulbs into my lighting setups," he says. "I also use it for my Christmas tree lights every year, so I can plug them in somewhere awkward, but I can still turn them on and off at will."
Senior News Editor Mark Wilson is a big fan of his Philips Hue Tap Dial Switch. This physical switch has four buttons and a dial, and can control nine different actions; it's a more complex alternative to the Smart Button. "I hate using my phone or voice controls for smart lights. My favorite feature is turning the dial to dim my Hue lights — it's so much better than tapping the buttons on other switches," says Mark. "It’s simple to use, while also being really versatile thanks to those four buttons, which can set scenes in different rooms."
Homes Editor Cat Ellis has a slightly different suggestion: if you're finding regular Hue bulbs too expensive, she recommends checking out the much cheaper Essential range. "I put a regular Philips Hue bulb and a Hue Essential bulb side-by-side in identical lamps, and it was almost impossible to tell the difference when shifting colors — I could only really notice a distinction when dialing down the brightness."
A smarter setup Philips Hue Tap Dial Switch Pros- Highly configurable
- Easy to set up
- Wireless with magnetic mount
- Only two color options
- Can be overkill for simpler Hue systems
- Compact, unassuming design
- Simple to use
- Works with Alexa, Google Assistant and HomeKit
- Requires Hue Bridge for control when you're not close by
- No energy monitoring functions
- Simple setup
- Can be mounted on a wall or used as a portable remote
- Customizable buttons
- Time-based control options
- Not as flexible as the Philips Hue Tap Dial Switch
- Only available in white
- Compact design
- Easy to set up and use
- Two wall-mounting options
- Limited functionality
- More expensive than the Hue Smart Wireless Dimmer


